Click the button below to add the Planmeca Proline PM 2002 EC Dental Panoramic X-Ray to your wish list. Related Products Planmeca PM 2003 Panoramic Dental X. Planmeca Intra User Manual. Separate collection for electrical and electronic equipment according to Directive 2002/96/EC (WEEE). Planmeca Intra X-ray Unit User.
Planmeca 2002 cc proline error
September 02, 2014 10:10
Hello, I've the Planmeca Proline 2002 cc Ortho and the machine reports me the Error 57 in the display. I've turn off and then turn on the Ortho, but the error continues.
Can anyone help me?
Thanks!
re: Planmeca 2002 cc proline error
September 03, 2014 09:01
remove the handswitch and turn unit off and on and see if it clears? could be a bad switch closed all the time
Log inor Registerto rate and post a comment
re: Planmeca 2002 cc proline error
September 03, 2014 09:01
Error 57 hand switch activated during switch on check this first
re: re: Planmeca 2002 cc proline error
September 03, 2014 12:54
Is the hand switch the button you press to take a radiography? I don't have this piece instaled. I only have the autoprint machine instaled. Sometimes after the error 57 appears HE 2 it seems like the
Keyboard doesn't respond to the key press. Should I connect the handswitch? How can i install it?
Thank you!!
to rate and post a comment
re: Planmeca 2002 cc proline error
September 03, 2014 09:02
Hi, you have problem in exposure button, praticaly is switched on. Open the exposure botton and also you can have problem in the extention cable. Put out the cable of extention exposure button and the error must deasapeare.
Send me a mail, and i send you technical manual.
Boian
to rate and post a comment
re: re: Planmeca 2002 cc proline error
September 03, 2014 12:54
Is the hand switch the button you press to take a radiography? I don't have this piece instaled. I only have the autoprint machine instaled. Sometimes after the error 57 appears HE 2 it seems like the
Keyboard doesn't respond to the key press. Should I connect the handswitch? How can i install it?
Thank you!!
re: re: re: Planmeca 2002 cc proline error
September 03, 2014 05:34
HE 2 Amalgam container is 100% full (only Metasys
or Dürr).
Replace or empty the container immediately.
The suction system cannot be used before the
container is emptied or replaced. See the
User’s manual for details.
send me an email address I will send you the service manual, if your keyboard does not respond and is used to initate the exposure it probably is bad
to rate and post a comment
re: re: re: re: Planmeca 2002 cc proline error
September 04, 2014 10:19
Amalgam in x-ray?!?
Log inor Register
to rate and post a comment
re: re: re: re: re: Planmeca 2002 cc proline error
September 05, 2014 09:38
that came from the service manual
re: re: re: re: Planmeca 2002 cc proline error
March 10, 2017 10:08
Hello Lenny, i need this service manual, can you send it also to me please medicapoli@gmail.com
Thanks so much
re: re: re: re: re: Planmeca 2002 cc proline error
March 10, 2017 10:33
OK I will send
Log inor Registerto rate and post a comment
re: re: re: re: re: re: Planmeca 2002 cc proline error
March 10, 2017 04:46
Thanks a lot
I need service manual panoramic rx planmeca PM2002 CC
Log inor Registerto rate and post a comment
What is the problem, which part of the manual do you need?
Log inor Registerto rate and post a comment
Tibor:
The problem I have is error 40 and 53, and if you have the manual would ask and I can share share another manual that interests of some I have.
regards
Oswaldo Quispe
to rate and post a comment
If you have the service Manual, I will be glad if you can share, we have one in our Hospital and would like to know the calibration procedure , current issue is KV too high and mA too low , We don't how to proceed for calibration of this system
Planmeca Pm 2002 Ec Proline User Manual 1
Log inor Registerto rate and post a comment
re: re: re: Planmeca pm 2002 cc
March 19, 2013 06:13
When the mA is low, the kV increases. I have the calibration procedure. Give me your e-mail.
I do not know how to use this forum for file transfer.
tibor@ivanszky.com
re: re: re: re: Planmeca pm 2002 cc
March 19, 2013 08:37
Tibor,
my mail is jmpovh@yahoo.com
Jean-Marc
re: re: re: re: Planmeca pm 2002 cc
April 11, 2017 10:18
I need the manual service of the Planmeca Proline PM 2002 CC, can you help me?
Please let me know.
Thanks
re: re: re: re: re: Planmeca pm 2002 cc
March 04, 2018 10:18
If you have the service Manual,can you share it? I would like to know the calibration procedure...Thank you in advance!
re: re: re: re: Planmeca pm 2002 cc
April 17, 2019 09:48
plz can uou send me calibration for planmeca cc 2002
dr.fawzyfayed@yahoo.com
re: re: re: re: re: Planmeca pm 2002 cc
April 18, 2019 12:31
You find manual in www.frankshospitalworkshop.com ,regards
re: re: re: re: re: re: Planmeca pm 2002 cc
April 23, 2019 10:06
it is not avalible
re: re: re: re: re: re: Planmeca pm 2002 cc
April 23, 2019 11:13
Planmeca Promax Calibration Manual
it is not avalible there
I would also like the service manual , please
Log inor RegisterPlanmeca Pm 2002 Ec Proline User Manual 2
to rate and post a comment
The problem I am having is the head will not come down, it is past limit switch and will not lower.
Log inor RegisterPlanmeca Pm 2002 Ec Proline User Manual Online
to rate and post a comment